WE ARE CLOSED FOR CHRISTMAS FROM THE 20TH OF DECEMBER TO THE 7TH JANUARY

DURING THIS TIME PLACING ORDERS IS SUSPENDED TO AVOID DISAPPOINTMENT

We would like to wish all our customers a very merry Christmas and a happy new year

Model Year: All Models
Change

Back 90-04 power steering pump V6 3.8

New Item
90-04 power steering pump V6 3.8
90-04 power steering pump V6 3.8
90-04 power steering pump V6 3.8
90-04 power steering pump V6 3.8
FORD AEROSTAR 1990-1997
FORD BRONCO 1989-1996
FORD BRONCO II 1990
FORD COUNTRY SQUIRE 1990-1991
FORD E-350 1992-1998
FORD EXPLORER 1991-2000
FORD F-150 1989-1996
FORD F-250 1989-1998
FORD F-350 1989-1997
FORD LTD CROWN VICTORIA 1990-1991
FORD MUSTANG 1990-2004
FORD RANGER 1990-2006
FORD TAURUS 1990-1995
FORD THUNDERBIRD 1990-1997
FORD WINDSTAR 1995-2000
LINCOLN CONTINENTAL 1990
LINCOLN MARK VII 1990-1992
MAZDA B2300 1994
MAZDA B3000 2002-2006
MAZDA B4000 1994
MAZDA NAVAJO 1991-1994
MERCURY COLONY PARK 1990-1991
MERCURY COUGAR 1990-1997
MERCURY GRAND MARQUIS 1990-1991
MERCURY SABLE 1990-2005

NOTE V6 3.8 ONLY

LARES MM12375 SpecificationsCap IncludedNoFilter IncludedNoHousing MaterialSteelInlet Attachment TypePipeInlet Quantity1Inlet Thread Size3/8 InchOutlet Attachment TypeO-RingOutlet Quantity1Outlet Thread DiameterM16-1.50Pulley Attachment TypePress-onPulley Belt TypeSerpentinePulley IncludedNoRemote ReservoirNoReservoir IncludedYes

 

Flushing and Bleeding Instructions

  1. Disable ignition system using recommended procedure in your service manual.

  2. Raise front wheels until just clear of ground.

  3. Place drain pan under power steering pump return port. Disconnect return line from power steering pump and

    place it in drain pan. Flush the power steering pump reservoir by pouring new fluid into the reservoir until the fluid runs clear. Be sure to use the fluid recommended for your vehicle. NOTE: DIRTY FLUID WILL VOID THE WARRANTY.

  4. Leave return line in drain pan. Cap the pump reservoir return port to prevent leakage.

  5. Fill power steering pump with new fluid recommended for your vehicle.

  6. While having someone watch the fluid level and adding fluid to the pump (Keep fluid above top of pump

    casting) crank the engine over using the ignition switch. (To prevent excessive starter wear; crank engine over for less than 20 second intervals.) Continue to add new fluid until return line runs clear. Reconnect pump return line.

  7. This completes the flushing procedure. Now begin bleeding the system.

  8. Fill power steering pump with new fluid recommended for your vehicle.

  9. While having someone watch the fluid level and adding fluid to the pump (Keep fluid above top of pump

    casting) crank the engine over using the ignition switch. (To prevent excessive starter wear; crank engine

    over for less than 20 second intervals.)

10. Whileyouarecrankingtheengineover,turnthesteeringwheellocktolockslowlyatleast4timestobleedthe

system. If you see any bubbles and/or foam enter the pump; stop and let the system rest until all of the bubbles

and/or foam has dissipated. Repeat steps 8-10 until bubbles and/or foam no longer enter the pump.
11. Reconnect ignition system. Lower wheels to the ground. Start engine and test drive car. If assist is smooth,

bleeding is complete. If assist is erratic, whines or fluid is foaming; repeat steps 8-10. 12. Draincoreandusingplugsprovided,returncoreinoriginalpackagingandbox.

page1image2402897472

Lares Corporation Steering Components • CALL 1.800.555.0767 • VISIT www.LaresCorp.com

page1image2402907456
£240.00 + VAT
£288.00 inc. VAT